The URL can be used to link to this page

Home My WebLink About102795 WESCO DISTRIBUTION INC - PURCHASE ORDER - 3307284 (2)Date: 11 /24/03 City of Fort Collins City of Fort Collins Page Number: 1 Purchase Order Number: 3307284 Delivery Date: 01/06/04 Buyer: DICK,OPAL Purchase Order number must appear on invoices, packing lists, labels, bills of lading, and all correspondence. Note: PER SPEC 373-104 Line Qty UOM 1 80 EA 7006-6860 Description 35' FIBERGLASS STLT POLE YARD POLE, STREETLIGHT, 35', DIRECT BURIED, TAPERED FIBERGLASS, FOR USE WITH ALUMINUM MAST ARM, PER SPEC. NO. 373-104, REV. L Bid #5591 Total Unit Price Extended Price 577.1000 46,168.00 $46,168.00 City of Fort Ci6lilijs Director of Purchasing and Risk Management This order is valid over $2000 unless signed by James B. O'Neill II, CPPO, FNIGP City of Fort Collins Accounting Department City of Fort Collins Purchasing, PO Box 580, Fort Collins, CO 80522-0580 PO Box 580 Phone: 970-221-6775 Fax: 970-221-6707 Email: info@ci.fort-collins.co.us Fort Collins, CO 80522-0580 CITY OF FORT COLLINS UTILITIES Light and Power Department P.O. Box 580 Fort Collins, CO 80522 SPECIFICATION NO: 373-104 Fiberglass Mast Arm Streetlight Poles PREPARED BY: W44-J401 Bill Bray Standard ngineer APPROVED BY: ""' Tim Sagen Standards Engineering Manager DATE: 3/1/2001 REV. L Table of Contents REVISIONDESCRIPTIONS....................................................................................................................................................2 1. SCOPE................................................................................................................................................................................4 2. REFERENCED STANDARDS.............................................................................................................................................4 3. DESIGN INFORMATION...................................................................................................................................................4 4. DIMENSIONAL REQUIREMENTS.....................................................................................................................................4 S. ADDITIONAL REQUIREMENTS.........................................................................................................................................4 6. SHAFT FINISH....................................................................................................................................................................5 7. PERFORMANCE.................................................................................................................................................................5 8. SHIPPING REQUIREMENTS.............................................................................................................................................5 9. QUALITY ASSURANCE.....................................................................................................................................................6 FIGURE1 - DIRECT EMBEDDED..........................................................................................................................................7 FIGURE2 - ANCHOR BASE..................................................................................................................................................8 APPENDIXA - MAST ARM....................................................................................................................................................9 APPENDIX B - APPROVED MANUFACTURERS................................................................................................................10 _ 3 373-104 REV. L 5.6. SPECIFIC REQUIREMENTS FOR 373-104-02 (Anchor Base) 5.6.1. The galvanized steel base assembly shall be epoxy bonded to the pole and coated with a polyurethane coating color matched to the pole. The base plate shall be in accordance with Figure 2 (Detail A) of this specification. 5.6.2. A 2.5" x 5' oval (ref ANSI C136.20, Figure 1) hand hole shall be provided. The hand hole shall be located 900 from armholes, 18" from the bottom of the pole, as shown in Figure 2. A color -matched, nonmetallic cover with stainless -steel captive screws and suitable means for attachment shall be provided. 5.6.3. A single 1/2" - 13NC tapped hole for grounding shall be drilled in the base on the same side as the hand hole, centered between the edge of the base plate and the edge of the pole sleeve. The hole shall be free of paint and debris. 6. SHAFT FINISH 6.1. The surface of the pole shall be smooth and shall be uniform and consistent for the entire length of the pole. 6.2. The color shall be equivalent to Benjamin Moor Ironclad Bronzetone #163-60. 6.3. The resin shall contain colored pigment to match the finish coat of the pole. Solid coloration shall be throughout the entire wall thickness of the pole. 6.4. The finish coating shall be Sherwin Williams Polane® HS pigmented polyurethane finish capable of withstanding exposure to ultraviolet, chemicals, and extreme weather conditions. Use of alternative coatings may be permitted with written approval from the City Fort Collins Utilities, L&P Standards Engineer. 6.5. The surface coating shall be uniformly applied so as to prevent craze -lines, bumps, and pinholes. The surface coating shall be minimum dry film thickness of 1.5 mils. 7.PERFORMANCE 7.1. All performance characteristics shall meet or exceed those of ANSI C136.20 as calculated in section 10.2.4.1 and 10.2.4.2 of said standard. The design limits to be used in calculating maximum wind loading, bending moment, and test force values are included in section 3 of this document. 7.2. Minimum Withstand Minimum withstand test force shall be the greater of either that calculated per ANSI C136.20 or 1300 pounds. 7.3. Static Deflection The maximum slope deviation shall be 0.12 inch in 12 inches, equivalent to a maximum theoretical angular rotation of 0 degrees 35 minutes. This limits the maximum static deflection to 1 % of the above ground pole shaft length when loaded with one arm and luminaire. 8. SHIPPING REQUIREMENTS 8.1. Fiberglass dust shall be removed from poles prior to wrapping for shipment. 8.2. Each pole shall be individually wrapped with a weather -resistant paper for protection in shipping and storage. 8.3. Poles shall be shipped on open bed trucks and packaged in such a manner as to prevent damage during shipping and handling. 373-104 5 SPECIFICATION NO. 373-104 Serial No. 373-104-01 B B 3'-4" 0 0.75" — 1 4.75" 4.75" T 12" I- 0 5.25" t .25" at C 0 5.356 t .25" at D C 02" 0 0.75" Manufacturer's Identification Tag VIEW BB (Drilled both sides) Plug wire hole on opposite side 14 inch max. Gfat E Ref. to Appendix A for am dimensional requirements TE yL•lG_ J 14 SECTION A Alternate antirotation methods ere subject to City approval 2.50" x 5" oval i A Figure 1 - Direct Embedded REV. L 7 373-104 11 Appendix A - Mast Arm SPECIFICATION NO. 373-105 V �-- A i Slotted 9 1/2" 1/2" 1 SECTION A e1 1/2" B 03/4 SPAN ORIGINAL: 5/28/85 REVISED: 1/31/89 Rev. A ISE I SPAN I SERIAL NO, STOCK N0. dejet TYeAlfi 8' 02 7006-0020 \` Pole Dia. ® B 5.356" * .25" SECTION B SPECIFICATIONS FOR ALUMINUM TAPERED OVAL MAST ARM 1) Arm shall meet or exceed ASSHTO (American Association of State Highway and Transportation Officials) standard specifications for aluminum lighting arms and fittings. 2) Arm shall have 2" N.P.S. tenon (2 3/8" O.D.). 3) Arm shall come with standard grounding lug, washer, and nut, and mounting hardware for single arm attachment. 4) Wire entry hole shall be grommetted for interior use through the pole plate. 5) Arm shall be urethane finished to match Benjamin Moore Ironclad Bronzetone point #163-60. and shall be individually packaged to prevent damage during shipping and storage. REV. L 9_ 373-104