Loading...
HomeMy WebLinkAboutWELLS FARGO PARKING LOT AND ATMS - MJA190003 - SUBMITTAL DOCUMENTS - ROUND 2 - SUPPLEMENTAL INFORMATIONNCR Proprietary Information ‐ not to be disclosed or reproduced without written consent. © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http://www.ncr.com., 2015 © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http:/ /www.ncr.com.All Rights Reserved Pre‐released DRAFT 04 NCR SelfServ™ 88 ATM Site Preparation ‐ DRAFT Dimensions ATM DIMENSIONS SECURITY BOLTS The island, or base, must be capable of withstanding the loading imposed by the anchor points for the bolts. Bolts and anchors must be supplied by the owning organisation. To meet security standards the ATM must be bolted to the island, or base, through all of the bolt holes, using bolts with anchor washers as specified below. Bolts and anchor washers are to be supplied by the owning organisation. Make sure that the island, or base, is capable of withstanding the loading imposed by the anchor points for these bolts. If an adjustable plinth is used, it must be bolted to the island, or base, to the same specification as the ATM. The minimum specification for bolts and washers to secure the ATM is:  Bolts  Type ‐ either resin anchor or shield anchor bolts  Size ‐ M16 (5/8 in.)  Minimum Length ‐ 150 mm (5.9 in.)  Strength ‐ high tensile (minimum ISO property class 8,8).  Washers  Type ‐ flat, steel (as per DIN7349 or equivalent)  Size ‐ M16 (5/8 in.)  Outer diameter ‐ no greater than 40 mm (1.58 in.)  Minimum thickness ‐ 6 mm (0.2 in.). BOLT HOLES The ATM should be bolted to the floor or plinth, through the holes marked ‘A’, using six bolts with anchor washers The hole marked ‘B’ enables a security sensor to be fitted. ISLAND DIMENSIONS The illustration below shows the dimensions for the minimum island size. The front of the facia is aligned to the front of the island. NCR recommends that the rear bollards are 102 mm (4.0 in.) in diameter, and positioned in line with the rear of the ATM, front bollards are 102 mm (4.0 in.) in diameter and positioned as near to the curb as possible without overhanging the edge. When locating the bollards allow sufficient working space for servicing the air conditioning unit (if fitted). Anti‐theft Bollards If anti‐theft bollards (also known as anti lassoing bollards) are to be fitted there must be a minimum gap of 60 mm (2.36 in.) between the ATM and the bollard for panel access. 922 mm (36.30 in.) including bumper 917 mm (36.10 in.) 1046 mm (41.18 in.) including bumper 1412 mm (55.59 in.) 702 mm (27.64 in.) 1040 mm (40.94 in.) NCR Proprietary Information ‐ not to be disclosed or reproduced without written consent. © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http://www.ncr.com. © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http:/ /www.ncr.com.All Rights Reserved Pre‐released DRAFT 04 Dimensions NCR SelfServ™ 88 ATM Site Preparation ‐ DRAFT CABLE ENTRY Cables enter the ATM through a hole in the base of the security enclosure. There should be a conduit hole in the island of sufficient size to allow the cables to be coiled ready to be brought into the security enclosure. Make sure that the island conduit hole is free from any material that may impede the cables. The hole should not be sealed or filled with concrete. The actual conduit hole may be larger than the that shown depending on the installation. Distribution boxes and any power and wiring conduits must not protrude above the surface of the island. ATM Cable Entry CEN Security Enclosures TOPPER HOLE LOCATION VENTS LOCATION ‐ AIR FLOW Unrestricted air flow is required on the right‐hand side of the ATM. There must be no obstruction of the vents at any time. If a third‐party surround/topper is fitted then equivalent venting or hot air extraction system must be installed within the surround/topper. 598 mm (23.54 in.) 315 mm (12.40 in.) 80 mm (3.15 in.) 60 mm (2.36 in.) 10 mm (0.39 in.) 385 mm (15.16 in.) 395 mm (15.55 in.) 122 mm (4.80 in.) 100 mm (3.94 in.) 40 mm (1.57 in.) 100 mm (3.94 in.) 50 mm (1.97 in.) 699 mm (27.52 in.) 738.5 mm (29.07 in.) 647 mm (25.47 in.) 31.5 mm (1.24 in.) NCR Proprietary Information ‐ not to be disclosed or reproduced without written consent. © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http://www.ncr.com. © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http:/ /www.ncr.com.All Rights Reserved Pre‐released DRAFT 04 Dimensions NCR SelfServ™ 88 ATM Site Preparation ‐ DRAFT FACIA ITEMS Heights and Depths Distance for Voice Guidance CLEARANCES ‐ FACIA OPENING CLEARANCES ‐ COSMETIC DOOR Facia Item Height from base of ATM Depth from front of collar Touchscreen 381 mm (15 in.) Top 1182 mm (46.54 in.) 26 mm (1.02 in.) Receipt 1181 mm (46.50 in.) 17 mm (0.67 in.) ID Scanner 1149 mm (45.24 in.) 18mm (0.71 in.) Card Reader 1098 mm (43.23 in.) 18 mm (0.71 in.) Contactless Card Reader (behind Facia) 1098 mm (43.23 in.) 18 mm (0.71 in.) PIN Pad Number 5 key 998 mm (39.29 in.) 12 mm (0.47 in.) Coin Exit 923 mm (36.34 in.) 15 mm (0.59 in.) Private Audio 902 mm (35.51 in.) 14 mm (0.55 in.) Cash Exit/Entry 865 mm (34.06 in.) 28 mm (1.10 in.) Scalable Deposit Module 865 mm (34.06 in.) 28 mm (1.10 in.) 5 NCR Proprietary Information ‐ not to be disclosed or reproduced without written consent. © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http://www.ncr.com., 2015 © 2015 by NCR Corporation, Duluth, Georgia, U.S.A. http:/ /www.ncr.com.All Rights Reserved Pre‐released DRAFT 04 Dimensions NCR SelfServ™ 88 ATM Site Preparation ‐ DRAFT SERVICING AREAS The optimum servicing area provides the best access to the ATM for all servicing and operation tasks. Wherever possible the ATM should be installed within the optimum servicing area. If the optimum area is not available then refer to Servicing Areas ‐ Minimum. However note that installing the ATM in the minimum servicing area may increase the servicing and/or upgrading time over a ATM installed using the optimum area. Always leave as much space as possible around the ATM to facilitate safe operation and servicing. Optimum Minimum 2908 mm (114.49 in.) 508 mm (20.0 in.) 1818 mm (71.6 in.) 3119.5 mm (122.81 in.) 934 mm (36.8 in.) 1040 mm (40.94 in.) 934 mm (36.8 in.) 793.5 mm (31.24 in.) 1 2 Service Area Panel Access 1 2 2459 mm (96.81 in.) 508 mm (20.0 in.) 1513 mm (59.57 in.) 2814.5 mm (110.81 in.) 1040 mm (40.94 in.) 508 mm (20.00 in.) 793.5 mm (31.24 in.) 1 2 Service Area Panel Access 1 2 508 mm (20.00 in.) 1040 mm (40.94 in.) 719 mm (28.31 in.) 700 mm (27.56 in.) JKL $ S 1234 5678 9 5 JKL $ S 1234 5678 9 Facia Item Distance from No. 5 Key Card Reader 1 110 mm (4.33 in.) Receipt 1 188 mm (7.40 in.) Private Audio 6 97 mm (3.82 in.) Cash Exit/Entry Right hand 7 140 mm (5.51 in.) Scalable Deposit Module Left hand 8 359mm (14.13 in.) Coin Exit 8 548 mm (21.57 in.) Touchscreen 381 mm (15 in.) Centre of screen 10 283 mm (11.43 in.) ID Scanner 10 563 mm (22.16 in.) Contactless Card Reader (behind Facia) 11 104 mm (4.09 in.) 11 12 10 9 8 7 6 5 4 3 2 1 S 1234 5678 9 $ 2035 mm (80.12 in.) 678 mm (26.69 in.) 634.5 mm (24.98 in.) 155.5 mm (6.12 in.) 102 mm (4.02 in.) 275 mm (10.83 in.) 73 mm (2.87 in.) 146 mm (5.75 in.) 615 mm (24.21 in.) 674 mm (26.54 in.) 2 850 mm (33.46 in.) 800 mm (31.50 in.) 770 mm (30.31 in.) 150 mm (5.91 in.) 76 mm (2.99 in.) 500 mm (19.68 in.) 135 mm (5.31 in.) 250 mm (9.84 in.) 500 mm (19.68 in.) 250 mm (9.84 in.) A A A A A A B 913 mm (35.94 in.) 152 mm (6.0 in.) 50.8 mm (2.0 in.) 50.8 mm (2.0 in.) 749 mm (29.49 in.) 749 mm (29.49 in.) 901 mm (35.47 in.) 901 mm (35.47 in.) 520 mm (20.47 in.) 520 mm (20.47 in.)